![\"\"](\"http:\/\/deltawireco.com\/wp-content\/uploads\/2020\/10\/Screen-Shot-2020-10-24-at-1.02.19-PM-300x163.png\")
<\/p>\nThe wire rope is pulled under load. As the tension increases, the tension in the wire rope also increases.<\/p>\n
Two types of tension occur in the wire:<\/p>\n
\u2022 Structural tension<\/p>\n
\u2022 Elastic tension<\/p>\n
<\/p>\n
The wire rope is made up of different structures, each containing a unique configuration of strands that are wound in a spiral around a core.<\/p>\n
![\"\"](\"http:\/\/deltawireco.com\/wp-content\/uploads\/2020\/10\/Screen-Shot-2020-10-24-at-1.02.31-PM-300x130.png\")
<\/p>\n
The cable cross-section, the distance between the wires and the strands, is minimized when applying tension. This contraction brings the core and rope elements closer together, which increases the cable length to some extent. By applying a load and closing the space between the wires and the strands, the structural tension of the rope is created.<\/p>\n
The amount of structural tension depends on various factors such as length, rope structure, diameter and cable bending. In applications where the same amount of traction is applied, cables with more wires usually have more traction than structures with less wires.<\/p>\n
After applying the initial load and creating tension, the diameter of the wire rope <\/span>It decreases slightly and its length increases. The change made in the rope wire is permanent.<\/p>\n Unlike structural tension, elastic tension is measurable. When the load is applied, the main material of the wire is stretched.<\/p>\n \n The cable wires are stretched separately, and the overall tension is proportional to the applied load. The elastic tension is calculated accurately using the above formula, unless it exceeds the efficiency point of the cable. After the force is released, the wire material regains its original length.<\/p>\n Designers must consider whether the inherent tensile properties of the tensioned wire rope <\/span>Is it important for their intended use or not. In most cases, structural tension and elastic tension are not important.<\/p>\n \u2022 Reduction of space between wires and strands when loading on wires<\/p>\n \u2022 The length of the rope increases<\/p>\n \u2022 It is stretched permanently<\/p>\n \u2022 Can it be removed? yes<\/p>\n \n \u2022 Wire materials are stretched<\/span> without assistance.<\/p>\n \u2022 The rope returns to its original length after the load<\/span> is released<\/p>\n \u2022 Temporary traction<\/p>\n \u2022 Can it be removed? No<\/p>\n \n While elastic tension cannot be removed, there are options to minimize or eliminate structural tension. As the wire rope is adjusted under load, structural tension typically occurs over a very small section of rope length. The length of the cable may be only 0.0025 to .01 times the length of the rope under load. For example, if the load is low, the total structural tension will be close to a quarter percent or less.<\/p>\n If a small endurance is required for a particular application, the structural tension of the wire rope can be changed using the following points:<\/p>\n \u2022 Preload (also known as pre-traction)<\/p>\n \u2022 Change the wire rope diameter<\/p>\n \u2022 Increase safety factor<\/p>\n If the right cable structure and diameter is chosen, most applications will not be adversely affected by traction. Many cables are designed with a higher safety factor than the workforce. For example, a 5,000-pound wire rope may be used with a total load of 2,500 pounds, which means that the cable works with a safety factor of 2. Safety factors can be increased if the structural tension in the wire rope is a concern.<\/p>\n The wire rope can be stretched in advance to achieve uniform tension. This process before installation, to the wire rope <\/span> Exerts a force. Pre-loading removes some structural tension to make the tension more predictable when using the wire.<\/p>\n <\/span>Cable design is essential to a successful program. If the amount of cable tension is important for your project, we can help you. <\/span><\/p>\n Contact us to talk to an expert to choose the best cable for your project.<\/p>\n For more information on the price of co2 welding<\/strong> wire and to buy co2 wire and other Delta wire<\/em> products, call 09121147793<\/strong>.<\/p>\n","protected":false},"excerpt":{"rendered":" Wire rope The wire rope is pulled under load. As the tension increases, the tension in the wire rope also increases. Two types of tension occur in the wire: \u2022 Structural tension \u2022 Elastic tension What is structural tension? The wire rope is made up of different structures, each containing a unique configuration of strands […]<\/p>\n","protected":false},"author":2,"featured_media":0,"parent":0,"menu_order":0,"comment_status":"closed","ping_status":"closed","template":"","meta":{"_bbp_topic_count":0,"_bbp_reply_count":0,"_bbp_total_topic_count":0,"_bbp_total_reply_count":0,"_bbp_voice_count":0,"_bbp_anonymous_reply_count":0,"_bbp_topic_count_hidden":0,"_bbp_reply_count_hidden":0,"_bbp_forum_subforum_count":0},"yoast_head":"\nWhat is elastic tension?<\/h2>\n
![\"\"](\"https:\/\/deltawireco.com\/wp-content\/uploads\/2020\/10\/Screen-Shot-2020-10-24-at-1.02.39-PM-300x221.png\")
<\/p>\nStructural tension versus elastic tension: Can it be eliminated?<\/h2>\n
Making cable \/ wire rope<\/h3>\n
Different sections for making 7×19<\/h3>\n
Contact DeltaWire for your questions<\/h2>\n